📍 Los Angeles County & SoCal 🔧 30+ Years Experience 🎥 CRT Broadcast Monitor Specialist 🏢 TEK Media Group
📞 (818) 244-4440
🇺🇸 WE WORK LOCALLY & NATIONWIDE 🇺🇸 Los Angeles • Southern California • Shipping Available Across the United States
TEK MEDIA GROUP • EST. 1994 🎥 BROADCAST MONITOR SPECIALIST 🇯🇵 SONY PVM-20M2U • PROFESSIONAL CRT MONITOR

Sony PVM-20M2U Professional
CRT Broadcast Monitor Restoration

By TEK Media Group – The CRT Broadcast Monitor Restoration Authority

I'm the owner and lead technician at TEK Media Group, and I've been restoring professional CRT broadcast monitors since 1994. The Sony PVM-20M2U is a legendary 20-inch 4:3 CRT professional video monitor – widely used in broadcast, post-production, and video editing suites. I offer complete restoration: full recap, CRT rejuvenation, convergence alignment, geometry calibration, and precision grayscale tracking to bring this legendary monitor back to its original factory performance. Every PVM that comes to my bench receives my personal attention. And yes, I serve customers nationwide – just ship your monitor to my Los Angeles facility.

📋 START SERVICE TICKET 📞 CALL (818) 244-4440
Home > Repair Services > Broadcast Monitor Repair > Sony PVM-20M2U Restoration
📋 A NOTE FROM MY WORKBENCH: The Sony PVM-20M2U is a professional-grade CRT broadcast monitor containing high voltages (up to 25kV). CRT work requires specialized knowledge, test equipment, and safety precautions. Over my 30+ years in this field, I've developed specialized techniques for restoring these monitors safely and correctly. I have the factory documentation, test equipment, and parts access needed for proper restoration. My email is jt@tekmg.com for direct inquiries.
⚠️ EXTREME SAFETY WARNING – PVM-20M2U SPECIFIC: This monitor contains lethal voltages even after power-off. The CRT anode can hold a 25kV charge for weeks. NEVER attempt internal repairs unless you are a qualified CRT technician. I use proper high-voltage discharge procedures and follow Sony factory service protocols. I cannot stress this enough – CRT work is dangerous.

About the Sony PVM-20M2U & My Approach

The Sony PVM-20M2U is a legendary 20-inch 4:3 CRT professional video monitor from Sony's acclaimed PVM (Professional Video Monitor) series. Featuring a high-resolution 20-inch Trinitron CRT, this monitor delivers excellent color accuracy, deep blacks, and reliable performance. It supports composite, S-Video, and component (RGB/YPbPr) inputs, making it a favorite for retro gaming, video editing, and broadcast monitoring. I've restored hundreds of PVM monitors over three decades, and I treat each PVM-20M2U with the meticulous care it deserves. I use premium replacement components and follow Sony factory service procedures to ensure your monitor performs to original specifications.

✅ WHY TRUST TEK MEDIA GROUP WITH YOUR SONY PVM-20M2U:
  • 30+ Years of Hands-On CRT Broadcast Monitor Restoration Experience
  • Specialized Knowledge of Sony PVM Series Monitor Systems
  • Full Power Supply & Deflection Board Recap
  • CRT Rejuvenation & Emission Testing
  • Precision Convergence Alignment (Static & Dynamic)
  • Geometry Calibration & Purity Adjustment
  • Grayscale Tracking & Color Temperature Calibration (D65)
  • Every Monitor Gets My Personal Attention – No Assembly Line
  • 90-Day Warranty on All Work
  • Nationwide Service – Secure Shipping Available Across All 50 States
  • Direct Email: jt@tekmg.com for quick responses

Restore Your Legendary PVM-20M2U Monitor

Click below to start your service ticket – I'll respond within 24 hours. Nationwide shipping available. Or email me directly at jt@tekmg.com.

🎫 START A SERVICE TICKET 🎫

Or call me directly: (818) 244-4440 | Email: jt@tekmg.com

Complete Sony PVM-20M2U Restoration Services I Offer

🔍 Full Diagnostic & Evaluation Complete assessment, CRT emission test, power supply check, deflection system evaluation, geometry analysis
⚡ Power Supply Rebuild Replace all electrolytic capacitors, check bridge rectifiers, test voltage regulators, verify all supply rails
🎛️ Deflection Board Recap Full recap of horizontal and vertical deflection circuits – critical for stable geometry
🖥️ CRT Board Service Recap CRT neck board, replace RGB output transistors, check cathode voltages, test G2/screen grid
💉 CRT Rejuvenation & Emission Testing Test CRT emissions with professional CRT tester/rejuvenator, restore weak guns if possible
🎯 Precision Convergence Alignment Full static and dynamic convergence alignment using crosshatch pattern
📐 Geometry & Purity Calibration Adjust pincushion, trapezoid, parallelogram, rotation, corner purity, and landing
🎨 Grayscale & Color Calibration Calibrate to D65 (6500K) with proper gamma tracking from 10-100% luminance
📡 Input Board Service Test and repair composite, S-Video, and component (RGB/YPbPr) inputs
🏆 COMPLETE FULL RESTORATION All services above – your PVM-20M2U will perform to original broadcast specifications
💡 WHAT MY RESTORATION INCLUDES: Full electrolytic recap (power supply + deflection + CRT boards) • CRT emission testing & rejuvenation • Full convergence alignment (static & dynamic) • Geometry calibration • Grayscale tracking to D65 • Input board testing • 90-day warranty.

🔧 Professional CRT Tips & Troubleshooting Techniques – From My Workbench

After 30+ years of repairing CRT broadcast monitors, I've compiled these proven tips and techniques for the PVM-20M2U. Feel free to email me at jt@tekmg.com with specific questions.

💡 TIP #1: No Power / Dead Unit – My Step-by-Step Approach
  • First, verify AC input voltage and check the IEC power cord – I've seen many "dead" monitors that just had a bad cord.
  • Check the main fuse on the power supply board – if blown, there's likely a short in the primary section. I check the bridge rectifier and switching MOSFETs.
  • Inspect the standby power supply – measure 5V standby rail. If missing, I check startup resistors and the PWM controller IC.
  • Common failure I see: Primary-side electrolytic capacitors on the power supply board – I always replace these with 105°C low-ESR types.
  • Check the main relay – if not engaging, I suspect either the power supply or a short on the deflection board.
  • Test all voltage rails: +135V (B+ for horizontal deflection), +24V, +12V, +5V, -15V.
💡 TIP #2: Dim CRT / Weak Emission – CRT Rejuvenation
  • First, test CRT emissions with my professional CRT tester/rejuvenator (B&K 490 or Sencore CR7000). I measure each gun (red, green, blue).
  • If emissions are low but not zero, I perform gentle rejuvenation – this can restore 50-80% of original brightness in many cases.
  • I always check G2 (screen grid) voltage and adjust if needed before rejuvenation.
  • After rejuvenation, I re-check emissions and recalibrate G2 and cutoff (black balance).
  • If the CRT is completely worn out (emissions near zero), replacement is the only option. I can help source a replacement CRT if available.
  • Prevention: Never run the monitor with excessive contrast/brightness – this accelerates cathode wear.
💡 TIP #3: Poor Convergence – PVM Series Common Issues
  • The PVM-20M2U has a convergence system with static and dynamic adjustments. I start with static convergence (center of screen).
  • I use a crosshatch pattern generator and adjust the convergence magnets on the CRT neck for red, green, and blue alignment at center.
  • For dynamic convergence, I access the service menu and adjust the convergence settings – this is painstaking work but essential for perfection.
  • I check the convergence amp ICs on the deflection board – failed capacitors here cause convergence drift.
  • If convergence changes with brightness, suspect the HV regulation circuit or CRT aging.
💡 TIP #4: Geometry Issues (Bow, Pincushion, Trapezoid)
  • First, replace all electrolytic capacitors on the deflection board – this fixes 80% of geometry problems.
  • Check the horizontal output transistor (HOT) and damper diode – replace if out of spec.
  • Adjust S-correction and pincushion using the service menu – I use a grid pattern for reference.
  • If the image tilts, adjust the rotation coil or yoke positioning.
  • Check the B+ voltage (135V) – if unstable, geometry will fluctuate. Recap the power supply first.
💡 TIP #5: Color Purity Issues (Patches of Wrong Color)
  • First, degauss the CRT using the internal degaussing coil – if the coil has failed, I use an external degaussing wand.
  • Check for external magnetic fields – speakers, transformers, or metal structures near the monitor.
  • Adjust the purity magnets on the CRT neck while displaying a red-only pattern – center the red field.
  • If purity is still off, the CRT may have been physically damaged or the shadow mask may be compromised.
  • Check the CRT landing adjustment in the service menu – fine-tune corner purity.
💡 TIP #6: No High Voltage / No Raster (Screen Dark, Filaments Lit)
  • Check for filament glow at the CRT neck – if lit, the power supply is working but HV isn't generating.
  • Listen for horizontal oscillator – if no 15.75kHz whine, the horizontal drive circuit isn't running.
  • Check the horizontal output transistor (HOT) – if shorted, replace and check the flyback transformer.
  • Inspect the flyback transformer (FBT) – cracks or bulging indicate failure. I have access to replacement flybacks.
  • Check HV shutdown circuit – a fault in the x-ray protection circuit can kill HV.
💡 TIP #7: Flickering or Collapsing Image
  • First, replace all capacitors on the vertical deflection IC – vertical collapse is almost always bad caps.
  • Check the vertical output IC – replace if cracked or shorted (I keep these in stock).
  • If the image shrinks or expands, check B+ voltage regulation – bad caps in the power supply cause this.
  • Check for cold solder joints on the deflection board – I reflow suspicious connections.
💡 TIP #8: Retrace Lines (Horizontal lines visible on screen)
  • Retrace lines indicate the G2 (screen) voltage is too high or the blanking circuit has failed.
  • First, adjust G2 down slightly while displaying a black pattern – lines should disappear.
  • If G2 adjustment doesn't fix it, check the blanking circuit on the CRT neck board – bad capacitors or transistors.
  • Check the flyback transformer's G2 control – if intermittent, the flyback may be failing.
💡 TIP #9: Out-of-Focus Image (Soft/Blurry)
  • First, adjust the focus control on the flyback transformer – mark the original position first.
  • If focus won't sharpen, the flyback transformer may be failing – replace it.
  • Check the CRT socket for corrosion – clean with DeoxIT.
  • A weak CRT can also cause focus issues – test emissions and rejuvenate if needed.
💡 TIP #10: My Capacitor Replacement Philosophy for PVM Monitors
  • Common capacitor failures: Power supply primary caps (10-15 years), deflection board caps (10-12 years), CRT neck board caps (10-12 years).
  • I use only 105°C low-ESR capacitors from Panasonic, Nichicon, or United Chemi-Con. No cheap imports – PVM monitors deserve the best.
  • I replace all capacitors on the power supply and deflection boards regardless of visual appearance – they age even if not bulging.
  • I document capacitor polarity before removal with photos – incorrect polarity causes immediate failure.
  • After recap, I verify all voltage rails and allow 60 minutes of burn-in before calibration.
💡 TIP #11: Input Board Issues (Composite, S-Video, Component)
  • Check input cables first – bad cables are a common source of "no signal" complaints.
  • If composite input is dead, check the video decoder IC (typically CXA or similar).
  • For component (RGB/YPbPr) issues, check the input switching IC and sync separator.
  • Clean input jacks with DeoxIT – corrosion causes intermittent connections.
💡 TIP #12: Remote Control / Control Panel Issues
  • If buttons are unresponsive, the tact switches may have failed – I can replace them.
  • Check the front panel ribbon cable connection to the main board.
  • If the OSD menu is missing but video displays, the OSD overlay IC may be faulty.
⚠️ EXTREME SAFETY NOTE FROM MY WORKBENCH: The PVM-20M2U contains lethal high voltage (up to 25kV at the CRT anode). I always discharge the CRT anode to ground before any service. I use proper HV probes and follow strict safety protocols. Do not attempt CRT work unless you are fully trained – serious injury or death can result.

🔍 Quick CRT Troubleshooting Reference Chart – From My Service Logs

SymptomMost Likely CauseMy Fix / Solution
No power, no LED, no filament glow Blown fuse, dead power supply Replace fuse, recap power supply, check HOT, check bridge rectifier
Filaments glow, but no raster (screen dark) No high voltage, horizontal oscillator dead, flyback failed Check HOT, check horizontal drive circuit, test/replace flyback, check B+
Dim image / low brightness Weak CRT emissions, low G2 voltage Test CRT emissions, rejuvenate if needed, adjust G2, check CRT board caps
Poor focus / blurry image Flyback focus control, weak CRT, CRT socket corrosion Adjust focus on flyback, test CRT emissions, clean socket with DeoxIT
Convergence off (color fringing) Convergence drifted, convergence amp failed, CRT aging Perform full static & dynamic convergence, check convergence amp ICs
Geometry issues (bowing, pincushion) Bad caps on deflection board, HOT issues, yoke misalignment Recap deflection board, check HOT, adjust service menu geometry settings
Color purity issues (color patches) Magnetized CRT, purity misadjusted, external magnetic field Degauss with internal coil or external wand, adjust purity magnets, check for external fields
Vertical collapse (horizontal line only) Vertical IC failed, bad caps on vertical circuit Replace vertical output IC, recap vertical deflection circuit, check power supply to IC
Retrace lines visible G2 too high, blanking circuit failed Adjust G2 down, check blanking circuit on CRT neck board, replace failed transistors
Flickering or unstable image Bad caps in power supply, cold solder joints, HV regulation Recap power supply, reflow deflection board, check HV regulation circuit

Deep Dive: My Sony PVM-20M2U Restoration Process

⚡ POWER SUPPLY (Critical for CRT Stability – I Never Skip This)
  • Main Filter Capacitor: Large snap-in electrolytic (220-470µF @ 400V) – I replace with 105°C, high-ripple types from Nichicon or United Chemi-Con.
  • Secondary Side Caps: All low-voltage electrolytics (10-2200µF) on the power supply are replaced with low-ESR, 105°C rated types.
  • B+ Regulation: I rebuild the B+ (135V) regulation circuit – critical for stable horizontal deflection and HV.
  • PWM Controller IC: I test and replace if faulty. Common failures: UC3842, MC34025, or similar.
  • Startup Resistors: High-value resistors (470k-1M) drift over time – I replace with 1% metal film.
🎛️ DEFLECTION BOARD (H & V Circuits)
COMPLETE DEFLECTION RESTORATION – MY PROCEDURE:
  • Electrolytic Capacitors: All SMD and through-hole electrolytics on the deflection board are replaced – horizontal and vertical circuits are very sensitive to bad caps.
  • Horizontal Output Transistor (HOT): I test the HOT and replace if out of spec (2SC3997 or similar). I keep genuine replacements in stock.
  • Vertical Output IC: I test and replace the vertical deflection IC – common failure (LA7833 or similar).
  • Flyback Transformer (FBT): I inspect for cracks or bulging – if failed, I replace with a genuine or high-quality aftermarket flyback.
  • Convergence Amps: I test the convergence amplifier ICs – they drift with age and cause convergence issues.
🖥️ CRT NECK BOARD
  • CRT Socket: I inspect for corrosion – clean with DeoxIT or replace if damaged.
  • RGB Output Transistors: I test the video output transistors – replace if leaky or out of spec.
  • G2 (Screen) Control: I verify and adjust G2 voltage – critical for black level and retrace elimination.
  • Cutoff (Black Balance) Adjustments: I calibrate cutoff for proper black tracking across all three guns.
  • Neck Board Capacitors: I replace all electrolytics on the neck board – they run hot and fail frequently.
💉 CRT REJUVENATION & TESTING
  • Emission Testing: I use a professional CRT tester/rejuvenator (B&K 490 or Sencore CR7000) to test red, green, and blue gun emissions.
  • Cutoff Testing: I test for shorts and gas in the CRT – these can cause intermittent issues.
  • Gentle Rejuvenation: If emissions are low but not zero, I perform gentle rejuvenation – this can restore significant brightness.
  • Post-Rejuvenation Verification: I re-test emissions and recalibrate G2 and cutoff.
  • CRT Replacement: If the CRT is beyond saving, I can help source a replacement (rare but occasionally available).
🎯 CONVERGENCE & GEOMETRY CALIBRATION
  • Static Convergence: I adjust the convergence magnets on the CRT neck for perfect center alignment using a crosshatch pattern.
  • Dynamic Convergence: Using the service menu, I perform convergence alignment – this is painstaking but essential for perfection.
  • Geometry Adjustments: I adjust pincushion, trapezoid, parallelogram, rotation, and corner pin using test patterns.
  • Purity Adjustment: I adjust purity magnets while displaying a red-only pattern for perfect color field uniformity.
  • Landing Adjustment: I adjust corner purity using the service menu's landing controls.

Sony PVM-20M2U – Component Overhaul Database

⚠️ Typical restoration: 60-80 electrolytic capacitors replaced across power supply, deflection, and CRT boards.
POWER SUPPLY BOARD
ComponentOriginal TypeMy Restoration Replacement Main Filter Capacitor 220-470µF @ 400V 105°C, High-ripple (Nichicon, United Chemi-Con) Secondary Side Caps 10-2200µF @ 16-200V Low ESR, 105°C (Panasonic FC / Nichicon PW) Startup Resistors 470k-1M ohm 1% metal film replacement B+ Regulator Caps 47-470µF @ 50-160V Low ESR, 105°C (Nichicon PW / Panasonic FC)
DEFLECTION BOARD
SectionCapacitor CountMy Replacement
Horizontal Deflection 8-12 caps Low ESR, 105°C, high ripple current rating
Vertical Deflection 6-10 caps Low ESR, 105°C (Panasonic FC / Nichicon PW)
Convergence Amps 4-8 caps Low ESR, 105°C, audio-grade where signal path
CRT NECK BOARD
ComponentActionMy Specification
Electrolytic Caps Replace All (6-10 caps) 105°C, long life (Nichicon PW / Panasonic FC)
CRT Socket Clean or Replace DeoxIT treatment or new socket if corroded
RGB Output Transistors Test & Replace Genuine replacements (2SC3671, etc.)

Precision Grayscale Calibration Procedure – As I Perform It

🎨 MY GRAYSCALE CALIBRATION PROCESS FOR PVM-20M2U:
  • Warm-Up: I power on the monitor for a minimum of 60 minutes before any calibration measurements – CRT stability is critical.
  • Colorimeter Used: I use a professional colorimeter (Klein K10-A or X-Rite i1Display Pro) with Calman or ColourSpace software.
  • G2 (Screen) Adjustment: I set G2 for proper black level – just at the point of cutoff.
  • Cutoff (Black Balance): I adjust cutoff (bias) controls for proper black tracking across all three guns.
  • Drive (White Balance): I adjust drive (gain) controls for D65 (6500K) color temperature at high luminance.
  • Grayscale Tracking: I verify grayscale from 10% to 100% luminance, ensuring Delta E < 2 across the entire range.
  • Gamma Calibration: I set gamma to 2.4 (broadcast standard) – CRT naturally has excellent gamma tracking.
  • Verification: I provide a detailed calibration report showing before/after measurements.
💡 NOTE: Proper CRT calibration requires professional equipment and experience. I've invested in the best tools over my 30+ year career. Your PVM-20M2U will leave my bench calibrated to broadcast standards.

Sony PVM-20M2U Specifications

.=Resolution .=600-800 TV lines (center) .=Aspect Ratio .=4:3 .=Color Temperature .=D65 (6500K) – adjustable to D93 .=Scan Formats .=480/60i, 576/50i (standard definition) .=Inputs .=Composite (BNC x2), S-Video, Component (RGB/YPbPr via BNC) .=Power Consumption .=Approx 120W (max) .=Weight .=Approx 60 lbs (27 kg)
ParameterSpecification
Display Type CRT (Cathode Ray Tube) – Trinitron
Screen Size 20 inches diagonal (4:3 aspect ratio)

Nationwide Service – We Ship CRT Monitors Across America

🇺🇸 WE SERVE CUSTOMERS IN ALL 50 STATES 🇺🇸 Ship your PVM-20M2U securely to my Los Angeles facility – I'll handle the rest

I've restored PVM CRT monitors for clients from New York to California, Texas to Washington. Shipping a 60lb CRT requires special care:

  • Secure Packaging: I'll provide detailed packing instructions for your PVM – double-boxing, high-density foam, and proper orientation (CRT face down is critical).
  • Pallet Shipping: For CRT monitors, I recommend palletized freight shipping for maximum safety.
  • Insured Shipping: I recommend fully insured shipping for your valuable broadcast monitor.
  • Nationwide Reach: No matter where you are in the United States, I can restore your PVM to factory specifications.
  • Direct Contact: Email me at jt@tekmg.com for a quick quote or consultation.

Frequently Asked Questions – Sony PVM-20M2U

❓ Why is the PVM-20M2U so popular for retro gaming?

The PVM-20M2U features a 20-inch Trinitron CRT with excellent color accuracy, deep blacks, and native support for RGB and component inputs. It's widely considered one of the best CRT monitors for retro gaming.

❓ How long does a full restoration take at your shop?

Typically 3-5 weeks due to the complexity of CRT restoration, convergence alignment, and calibration. Rush service available – just ask me directly.

❓ Do you really offer nationwide service for CRT monitors?

Yes! I serve customers across all 50 states. Shipping a 60lb CRT requires special packing – I'll provide detailed instructions to ensure safe transport.

❓ Can you rejuvenate a weak CRT?

Yes – I have professional CRT rejuvenation equipment. Gentle rejuvenation can restore 50-80% of original brightness in many cases.

❓ Do you have spare parts for the PVM-20M2U?

Yes, over 30 years I've accumulated a stock of flyback transformers, HOTs, vertical ICs, and other critical components.

❓ Do you warranty your work?

Yes, 90-day warranty on all parts and labor. I stand behind every restoration I complete.

❓ How do I ship a 60lb CRT monitor safely to you?

I'll provide detailed packing instructions. CRT monitors must be shipped face-down with high-density foam. I recommend freight shipping with insurance.

❓ How can I contact you directly?

Call me at (818) 244-4440 or email jt@tekmg.com. I respond to emails within a few hours during business days.

❓ Do you offer local pickup and delivery in Los Angeles?

Yes, for clients in Los Angeles County, Orange County, Ventura County, Riverside County, and San Bernardino County. I can arrange pickup for CRT monitors.

My Service Area – Local & Nationwide

🇺🇸 NATIONWIDE SERVICE AVAILABLE 🇺🇸 Ship your Sony PVM-20M2U securely to my Los Angeles facility – I serve customers across all 50 states

Local Service: Los Angeles County, Orange County, Ventura County, Riverside County, San Bernardino County, and surrounding Southern California areas. I can arrange pickup and delivery for these CRT monitors.

Nationwide Service: For customers outside Southern California, I offer secure palletized shipping options. I'll provide detailed packing instructions for your CRT monitor and work with fully insured freight carriers. I've restored PVM monitors for clients from New York to Texas to Seattle to Florida.

Contact Me: For questions or to schedule service, call (818) 244-4440 or email jt@tekmg.com.

Los Angeles County: LA Burbank Glendale Santa Monica Hollywood Pasadena Beverly Hills
Orange County: Santa Ana Anaheim Irvine Costa Mesa Newport Beach
Nationwide Shipping: New York Texas Florida Illinois Colorado Washington Georgia All 50 States

TEK Media Group — Professional CRT Broadcast Monitor Restoration Since 1994

📞 (818) 244-4440 | ✉️ jt@tekmg.com

Serving Los Angeles, Orange County, Ventura, Riverside, San Bernardino, and nationwide via secure palletized shipping

Specializing in Sony PVM/BVM, JVC, Ikegami, and Professional CRT Broadcast Monitors

Sony PVM-20M2U Specialist • CRT Rejuvenation • Convergence Alignment • 30+ Years Experience

Every PVM monitor gets my personal attention – I'm the technician who does the work, not a call center. Nationwide service available. Email me directly at jt@tekmg.com.

Call
Mobile
(818) 244-4440
Toll Free: (800) 255-5045