Mark Levinson No. 335 Stereo
Amplifier Restoration

About the Mark Levinson No. 335 & My Approach

The Mark Levinson No. 335 stereo amplifier (circa 2000-2007) is a reference-grade power amplifier from the legendary 33x series. Delivering 250 watts per channel into 8 ohms (500 watts into 4 ohms), the No. 335 features a fully balanced, dual-mono design, massive toroidal transformers, and high-bias Class A/AB operation. Known for its effortless power, stunning transparency, and rock-solid build quality, the No. 335 remains a favorite among discerning audiophiles worldwide. I've restored dozens of Mark Levinson amplifiers over three decades, and I treat each No. 335 with meticulous care, using premium replacement parts while preserving the original reference-grade sonic character.

Complete Mark Levinson No. 335 Restoration Services

Deep Dive: My Mark Levinson No. 335 Restoration Process

• Main Filter Capacitors: Massive snap-in or screw-terminal electrolytics (typically 4-8 large caps, 10,000-22,000µF each) – I replace with high-ripple, low-ESR, 105°C rated types (Nichicon KG, Cornell Dubilier, or Kemet).
• Bridge Rectifiers: I test and replace if noisy, upgrade to ultra-fast soft recovery types for lower noise floor and cleaner power delivery.
• Soft Start / Thermistors: I check inrush current limiters and replace if cracked or out of spec.
• Secondary Filter Caps: All smaller electrolytics on the power supply board and driver boards are replaced.
• Transformer Check: I verify toroidal transformer output voltages and listen for mechanical hum.

• Output Transistor Testing: The No. 335 uses multiple pairs of high-power transistors per channel (typically TO-3P or TO-247 packages). I test each transistor for gain (hFE), leakage, and breakdown voltage. I replace failed or mismatched devices with genuine, matched replacements.
• Emitter Resistors: I measure and replace any out-of-tolerance emitter resistors (typically 0.22Ω-0.47Ω).
• Thermal Compound Replacement: I remove old, dried thermal compound from output transistors and heatsinks, apply fresh high-quality thermal paste for optimal heat transfer.
• Bias Transistor (Vbe Multiplier): I check the bias spreader transistor and ensure proper thermal tracking.

• Initial Bias Setting: Using a precision DMM, I set bias current per channel to factory specifications (typically 50-150mA depending on version).
• Warm-Up Stabilization: I allow the amplifier to reach thermal equilibrium (30-45 minutes) and re-check bias.
• Thermal Tracking Verification: I monitor bias current as the amplifier heats up to ensure stable operation.
• Final Bias Adjustment: I lock in bias settings and verify distortion at low and high power levels.

• Speaker Relay: I test the output relay for contact resistance, replace if pitted or intermittent.
• DC Offset Protection: I verify the DC detection circuit triggers correctly.
• Thermal Cutoff: I test thermal switches mounted on heatsinks.
• Over-Current Sensing: I check current sense resistors and comparator circuits.

Common Mark Levinson No. 335 Problems I Solve

#1 Power Supply Capacitor Aging

Symptom: Increased noise floor, loss of dynamics, reduced bass authority, hum.
My Solution: Complete recap of main filter capacitors and all secondary power supply electrolytics.

#2 Output Transistor Failure

Symptom: Amplifier goes into protection, distorted output, no sound from one channel, blown fuse.
My Solution: Test all output transistors, replace failed devices with genuine, matched replacements, recalibrate bias.

#3 DC Offset Drift

Symptom: Protection relay engages intermittently, audible thump on power on/off, DC at speaker terminals.
My Solution: Replace differential pair transistors, adjust DC offset to near 0mV, check servo circuit capacitors.

#4 Bias Drift / Unstable Bias

Symptom: Amplifier runs too hot, distortion at low levels, bias current fluctuates.
My Solution: Replace bias trim pots, check Vbe multiplier transistor, recalibrate bias to factory specs.

#5 Speaker Relay Not Engaging

Symptom: No sound, relay clicks but no output, intermittent output.
My Solution: Replace output relay, check protection circuit capacitors, verify DC offset.

#6 One Channel Distorted / Low Output

Symptom: Imbalance between channels, distortion on one side.
My Solution: Check driver board components, test output transistors, verify power supply rails, check input relay.

#7 Excessive Heat / Thermal Shutdown

Symptom: Amplifier shuts down after playing loudly, runs extremely hot.
My Solution: Check bias current (likely too high), replace dried thermal compound, verify heatsink mounting, test thermal switches.

Mark Levinson No. 335 – Component Overhaul Database

Precision Calibration & Performance Testing

Mark Levinson No. 335 Specifications

Frequently Asked Questions – Mark Levinson No. 335

My Service Area – Local & Nationwide

Local Service: Los Angeles County, Orange County, Ventura County, Riverside County, San Bernardino County, and surrounding Southern California areas. Local pickup and delivery available.

Nationwide Service: For customers outside Southern California, I offer secure shipping options. I provide detailed packing instructions for heavy amplifiers and work with fully insured carriers to ensure your valuable No. 335 arrives safely. I've restored equipment for clients across the United States.